Update firmware 4.5.1 to 4.6.6 experience
Verfasst: 04 Jun 2020, 00:22
Start TXT
Start RoboPro
Connection: USB cable.
Start Putty with screen -r (optional)
Start test interface.
Popup with message update firmware. Answer with Ok within 2 sec. If you wait to long the update doesn't work.
During +/- 1:40 min nothing is happening.
On the console screen (repeating):
Then their is a green line on the message box and the time runs from 1:40.
On the console screen you will see now:
After this, the uploading of the installation file to the TXT is ready and the installation proces starts on the TXT.
Do nothing and wait until the TXT will switch of after some minutes.
This first time I switch on the TXT, it shows a grey screen.
After switching off and on the TXT boot fine and shows his normal screen.
The update was done.
Start RoboPro
Connection: USB cable.
Start Putty with screen -r (optional)
Start test interface.
Popup with message update firmware. Answer with Ok within 2 sec. If you wait to long the update doesn't work.
During +/- 1:40 min nothing is happening.
On the console screen (repeating):
Code: Alles auswählen
Received send file block command
Received send file block command
Received send file block command
IOs/s DL=0 OL=0, Cam DL=0 OL=0, I2C tr=0 by=0
Received send file block command
Received send file block command
On the console screen you will see now:
Code: Alles auswählen
Received send file close command
Received send file open command
Received send file block command
Received send file close command
Received run command command
total 56136
drwx------ 2 root root 80 Jun 3 23:37 .
drwxrwxrwt 7 root root 640 Jun 3 23:37 ..
-r-x------ 1 root root 57477296 Jun 3 23:37 executable
-r-x------ 1 root root 512 Jun 3 23:37 signature
+ readlink -f /tmp/tmp.kgcoab/executable
+ SCRIPTPATH=/tmp/tmp.kgcoab/executable
+ dirname /tmp/tmp.kgcoab/executable
+ SCRIPTFLDR=/tmp/tmp.kgcoab
+ [ 0 = 0 ]
+ + grep -n -m 1 ^PAYLOADTOOLSBEG:$ /tmp/tmp.kgcoab/executable
cut -d : -f 1
+ payloadtoolsbeg_match=350
+ cut -d : -f 1
+ grep -n -m 1 ^PAYLOADTOOLSEND:$ /tmp/tmp.kgcoab/executable
+ payloadtoolsend_match=495
+ payloadtools_start=351
+ payloadtools_length=144
+ tail -n +351 /tmp/tmp.kgcoab/executable
+ head -n 144
+ openssl enc -base64 -d
+ gzip -d -
+ chmod u+x /tmp/tmp.kgcoab/ShowProgressOld
+ basename /tmp/tmp.kgcoab/executable
+ [ executable = executable ]
+ umask 077
+ mktemp -d -p /tmp
+ EXECFLDR=/tmp/tmp.4AAlkL
+ mv /tmp/tmp.kgcoab/executable /tmp/tmp.4AAlkL/executable
+ mv /tmp/tmp.kgcoab/signature /tmp/tmp.4AAlkL/signature
+ mv /tmp/tmp.kgcoab/ShowProgressOld /tmp/tmp.4AAlkL/ShowProgressOld
+ touch /tmp/tmp.kgcoab/executable
+ touch /tmp/tmp.kgcoab/signature
+ SCRIPTFLDR=/tmp/tmp.4AAlkL
+ SCRIPTPATH=/tmp/tmp.4AAlkL/executable
+ screen -m -d -S update /bin/sh -c /bin/sh /tmp/tmp.4AAlkL/executable restart 2>&1 | /tmp/tmp.4AAlkL/ShowProgressOld
+ exit 0
IOs/s DL=0 OL=0, Cam DL=0 OL=0, I2C tr=0 by=0
[screen is terminating]
Do nothing and wait until the TXT will switch of after some minutes.
This first time I switch on the TXT, it shows a grey screen.
After switching off and on the TXT boot fine and shows his normal screen.
The update was done.