Hallo allerseits,
im Forum habe ich nichts Explizites zu folgendem Problem gefunden, obwohl da und dort ähnliche Probleme berührt wurden.
Mein Sohn ist seit kurzem stolzer Besitzer eines 2. Robo-TX-Controllers. Diesen haben wir auch brav zur Extension 1 gemacht.
Das wird in der 3. Zeile des Displays auch angezeigt. Der 1. Robo-TX-Controller ist Master, auch das zeigt Controller #1 an.
Dann haben wir die beiden Controller über die Extension-Ports verbunden.
Geht man nun in Robo-Explorer auf "Verbindungstest", so erscheint nur der 1. Controller. Der Knopf, mit dem die Extension auszuwählen wäre, bleibt gegraut und ist nicht anzuwählen. Der Master-Controller meldet auf dem Display die "Online-Verbindung mit BT", die Extension 1 nur "Online".
Meine Frage ist nun: Wie teile ich Robo-Explorer mit, daß am Master eine Extension steckt ?
Gibt es eine bestimmte Reihenfolge, in der alles eingeschaltet werden muß ?
Braucht man eine bestimmte Firmware ?
Gibt es noch einen Software-Knopf bei Robo-Explorer ? (Wir haben die Version 2.1.4.2)
????
Für einen Tipp wäre ich, auch im Namen meines Sohnes, der sein ganzes Taschengeld für den 2. TX-Controller ausgegeben hat, sehr dankbar.
Vielen Dank
Das Spielkind
Probleme mit 2. Robo-TX-Controller als Extension
Moderator: fischertechnik Mitarbeiter
Forumsregeln
Bitte beachte die Forumsregeln!
In dieser Unterkategorie können nur fischertechnik-Mitarbeiter und Moderatoren antworten!
Bitte beachte die Forumsregeln!
In dieser Unterkategorie können nur fischertechnik-Mitarbeiter und Moderatoren antworten!
Re: Probleme mit 2. Robo-TX-Controller als Extension
Sorry, Rückzug, habe die Rubrik übersehen UMueller
Re: Probleme mit 2. Robo-TX-Controller als Extension
A pure technical answer.
About this problem 2 remarks:
-)
always connect two TX-C with different EXT slot:
(EXT slots are the connectors on the left and right of the display .)
TX-C 1 EXT1 <==cable=> TX-C 2 EXT2
or
TX-C 1 EXT2 <==cable=> TX-C 2 EXT1
-)
The RoboPro can read which extensions are connected and active. So you don't need to notify RoboPro that there are extensions available.
In the "Main program" tab of RoboPro, there is a subtab "Properties".
Under "Interface location" you will find a list about the mapping of the TX-C to the RoboPro variable.
Use the right variable name inside RoboPro when you are using an actuator or sensor on that TX-C.
--)
WIth this "Interface location" list you can change from extension with out changing the program.
For example:
EM1= Extension 1 (default setting)
You are using EM1 in your program.
(Extension 1 in used in a model X)
Now you have another model X with an Extension 3. And you like to test your program also with the second model.
This is possible:
a)
Hardware: Connect the Extension 3 to the master or the Extension 1
b)
Software: Change in the "Interface location" list two entries:
"EM3= Extension 3" into "EM1 = Extension 3"
"EM1 =Extension 1" into "XXX = Extension 1"
When you run the RoboPRo program, EM1 is now connected with the second model.
About this problem 2 remarks:
-)
always connect two TX-C with different EXT slot:
(EXT slots are the connectors on the left and right of the display .)
TX-C 1 EXT1 <==cable=> TX-C 2 EXT2
or
TX-C 1 EXT2 <==cable=> TX-C 2 EXT1
-)
The RoboPro can read which extensions are connected and active. So you don't need to notify RoboPro that there are extensions available.
In the "Main program" tab of RoboPro, there is a subtab "Properties".
Under "Interface location" you will find a list about the mapping of the TX-C to the RoboPro variable.
Use the right variable name inside RoboPro when you are using an actuator or sensor on that TX-C.
--)
WIth this "Interface location" list you can change from extension with out changing the program.
For example:
EM1= Extension 1 (default setting)
You are using EM1 in your program.
(Extension 1 in used in a model X)
Now you have another model X with an Extension 3. And you like to test your program also with the second model.
This is possible:
a)
Hardware: Connect the Extension 3 to the master or the Extension 1
b)
Software: Change in the "Interface location" list two entries:
"EM3= Extension 3" into "EM1 = Extension 3"
"EM1 =Extension 1" into "XXX = Extension 1"
When you run the RoboPRo program, EM1 is now connected with the second model.
- Dirk Haizmann ft
- fischertechnik Mitarbeiter
- Beiträge: 1126
- Registriert: 09 Nov 2010, 08:48
Re: Probleme mit 2. Robo-TX-Controller als Extension
@spielkind
Ich hoffe du kommst mit der (englischen) Antwort von vleeuwen zurecht.
ft
Ich hoffe du kommst mit der (englischen) Antwort von vleeuwen zurecht.
ft